ERW Logo

ABOUT
US
CONTACT
US


Canada Flag
Please call us for a distributor near you!
1-800-403-3279
Need help determining which heater is right for you?
Call or email us - we're happy to help!
US Flag

We manufacture a wide variety of heating equipment for residential, commercial,
agricultural, and industrial use. All of our products are 100% North American made,
and are covered by our industry best
4 Year "No Ifs, Ands, or Buts" Guarantee

Satisfaction Guaranteed

THE HEATWAVE
Residential Shop/Garage Radiant Tube Heaters

The Safe, Efficient and Affordable Solution for Heating your Garage or Workshop. Perfect for Smaller Garages & Workshops With Lower Ceilings.

The Heatwave

SLEEK, SMALL, COMPACT

The Heatwave in GarageAt 40,000 BTUH, 8' in length, and only 8 3/4" from bottom to top, the Heatwave can fit in smaller shops easily, and can be installed in building with ceilings as low as 8'. Perfect for garages and workshops, the Heatwave can also be used anywhere that space constraints make other heating equipment difficult or impossible to use.

READY TO HANG RIGHT OUT OF THE BOX

Heatwave in a GarageThe Heatwave comes factory assembled and ready to hang right out of the box - everything you need is included for easy installation. 5' of concentric venting, side wall vent termination, a 24V thermostat, flexible gas connector, and hanging chain are provided.

Exhaust and air intake venting are run through a 5" dia. side wall concentric duct for a clean, sleek installation. 5' vent extension and 90 degree vent elbows are available.


THE BURNER
  • 40,000 BTUH
  • Natural gas (model GH40N) and propane (model GH40P) fired models built to order with no field conversions required.
  • Reliable electronic hot surface ignition.
  • Built with 100% North American made electronic controls.
  • Continuous combustion monitoring with three to five ignition trials before 100% safety lockout.
  • Totally enclosed blower motor with internal thermal overload protection. Blower motor is externally mounted for ease of accessibility and to simplify intake air connection (4" combistion air intake duct adapter comes standard).
  • Dual air proving switches monitor combustion air and exhaust airflow for safety.
  • Flame observation port to visually observe combustion.
  • Factory ready to accept either 24V or 120V controls.

THE RADIANT TUBE

  • Emitter tubes are 3" diameter, 16 gauge North American steel.
  • Primary combustion tube made of high temperature, high emissivity specialty alloy.
  • Secondary tubes constructed of 16 gauge carbon steel for high emissivity.
  • Swedged tube for ease of installation - no couplers or clamps required at joints.
  • Emitter tubes provided with a 20 year burnout guarantee.

    THE REFLECTORS


  • Highly efficient, wide angled aluminum reflectors - engineered to reflect maximum radiant energy over the largest effective area possible.
  • Highly polished material for increaded reflectivity.
  • Steel hangers with suspension points for both flat and angle mounting of reflectors.

  • SPECIFICATIONS AT A GLANCE

    HEATWAVE DIMENSIONS
    LENGTH: 8'
    WIDTH: 14'
    HEIGHT: 8 3/4"

    Typical Heatwave Installation

    Heatwave Horizontal ClearancesHeatwave Angled Clearances

    Heatwave Specifications


    DOCUMENTS


    PDF

    Operation and Installation Instructions
    Full installation/operation instructions for the Heatwave radiant tube heater (PDF 3.1 MB)



    Intertek ETL All of our products have been tested to CSA/CGA & AGA standards Intertek ETL Laboratories to 100% compliance with both Canadian and US gas code.
    100% insurance company approved!



    EASY RADIANT WORKS
    12288 BRAWN RD. WAINFLEET, ON, CANADA
    LOS 1V0

    PH. 905-899-3473
    TF. 800-403-3279
    FX. 905-899-2262

    erw@vaxxine.com